This is because Epson Perfection scanners are not really calibrated in the factory (well come on, they only cost $700). So for those seeking the best out of their scanner dollar (and lets face it, you can't buy the Nikons anymore) we try to make the tools we have just that bit sharper than they are 'out of the box'
I thought I'd share with you the little shortcut I use to find the sweet spot. Its a stack of coins. In this case its the 5c coin.
Sticking them on the glass so that they hang over each other one can see pretty quickly where the focus point is.
Obviously coin 1 is on the glass ...
Its at coin 4 through to 5 that things appear their sharpest. So, now by measuring the coin thickness you can quickly set up your Better Scanning holders to get the best out of your film scans.
How much better?
Well about like this:
and this is a 100% crop of a 1200dpi scan of a slide which I wasn't really that happy with (crummy lens). Chalk and Cheese isn't it ...
Hmmm ... speaking of which, its time for some cheese to go with my red wine I think...
Happy Adjusting
Wow, that is an enormous distance. Neat trick with the coins.
ReplyDeleteHi Jao
ReplyDeletethanks for the comment. I normally use microscope slides with permanent marker on it, but guessed that coins would be more available.
I had posted similar to this on forums before but thought that since my blog gets more traffic I may actually help more people this way.
The distance is rather large, its larger than that on my 4870. Makes me wonder if its a larger to enable them to make the scanner a few mm smaller (noone told engineering so they didn't compensate) and chalk up a win for the marketing department ...
:-)
My 4990 Epson was exactly the opposite: it focused too far into the glass! Never managed to get perfect focus out of it.
ReplyDeleteIt's gone now, after a violent encounter with the floor boards...
Wonder if this problem was fixed in all new ones or it's something we can take it back to Epson to get fixed if it happens again?
Well I reckon it should be a warranty issue. Perhaps a quick test like this can save a lot of frustration.
ReplyDeleteThough I already dialed in my Betterscanning holder, I thought I'd try this during my last scanning run. The problem I found in doing it is getting sufficient light underneath the coins to make the details visible. How did you accomplish this? A flashlight to the side? That didn't work well for me.
ReplyDeleteI tried scanning in document mode (so it is lit from underneath), but I don't trust that the focus area is the same (I highly doubt it, though I don't know how they would accomplish this mechanically unless the scanning CCD is physically shifted lower by the machine.
Chuck
ReplyDeleteUse silver coins and pull the curves up to see it more clearly.
Definitely don't do this in reflective setting as the scanner changes focus
:-)
Wow!!! After a couple of years with a soft Epson v700 and their standard neg and slide holders, I stumbled upon your fantastic idea!!!!! I've organised a bit of a shim via .5mm hard plastic sheeting. I never thought that our 5 cent piece was worth anything until today! Thanks!!!
ReplyDeletesam
After ~12 years my 3170 went out of focus because I did not fit the part holding the glass down properly at the back after cleaning the glass. I did not notice straight away, but when I scanned some very sharp prints and their negs it was clear the focus was poor.
ReplyDeleteWhat was the last thing I did before this? Cleaned the glass. So I checked the assembly and found it was about 2mm above where it should have been.
You deleted my comment - normally I save to clip board but forgot.
ReplyDeleteYou did it again when I click on publish.
My 3170 has worked perfectly for about 12 years, but the scans went out of focus after I had cleaned the glass. I failed to seat the glass assembly properly so when the 2 screws were tightened the rear was about 2mm higher than it should be. I re-fitted the glass and my scans are now back in focus. I did try the coin trick but this made things worse - that's when I checked that the glass was seated correctly.
John
ReplyDeleteI did not delete your comment, its still there ... if you failed to save the comment or are too impatient to await my approval of comments (a measure to prevent spam on my blog) then that's not my fault.