Saturday, 6 June 2026

Blew a fuse

So, the other day I went for a ride and found that my headlight wasn't working (I was on a short ride). I tried high beam and it was, so I thought "blown bulb" however ...  it was then I noticed that my neutral light was very dim and that the indicators were not working properly (not blinking).

After I got home I pulled the headlight off and checked the bulb.



All was fine, which wasn't a relief, because now I had to find what the problem really was. I lifted the seat and found that a fuse (was blown). 

Now its worth revisiting the bike and note that its not "original". As you can see below the airbox is missing and you can make out a tray under the seat which holds most of the electricals:


Including the slim battery:


which has a "quick plug" type connection with a built in main fuse (of the blade type).

It was rated at 15A and I noted (in the manual) that the main fuse should be a 20A. I replaced the fuse then I checked wires to look for some sort of short (wire rubbing against inside of the metal bucket is a candidate) and all appears fine.

This leaves me with 2 questions:
  1. what caused the fuse to blow
  2. how then (with the fuse being blown) was my high beam getting power?
So I pulled the fuse and put my Multimeter (set to Amps and it reads up to 10) and began looking for problems. I quickly found that the headlight worked sometimes, but with a bit of movement went off and the meter rapidly climbed. I'd then turn off the light and resume after "moving it till it was ok again".

It took me a couple of days (no more than 4 hours each session) to work out that it was actually the loom rubbing against the steel of the bike ...


because when I relieved this (lifting up) the much higher power drain went away and the headlight operated normally.

I looked around and found:


1. the loom ran under the cable for the exhaust valve decomression cable and



2. the loom ran under a bracket which supports the tank from wobble. I thought perhaps if this was lifted up it would free the loom from fouling the bracket and consulted the manual:


ahhh hah ... so somehow this had been put together wrong some time back (probably 2016 when it was imported into Australia).

So I re-ran the cable back under the loom and ran the cable over the support:


which then lifted the loom away from that cable:


and took the weight off where the loom goes into the headlight support bracket.



... which I also "splinted" with some plastic (cut a section from a 2L milk bottle), some duct tape and a cable tie (which should also prevent it pulling out of that (if it feels so inclined).

So, its now been test ridden and seems to be doing ok ... 

I fully appreciate that there will be some copper getting atmosphere in there now, which is less than ideal, but to do that job I'd have to strip back even more than I did as well as undo the loom searching for the wire, cutting and joining in a new piece and putting it all back together (probably adding several hours).

Lets see how long it lasts :-)

Monday, 25 May 2026

Claude the confident bullshitter

Its really interesting now that DuckAI is providing the "thinking" responce of its AI's as well as its output. So I asked Claude:

User prompt 1 of 2 - 5/25/2026, 3:19:41 PM:
what is the etymology of the finnish word 'myrsky'

and it thought and answered:

"Myrsky" (meaning "storm" in Finnish) has roots in Old Norse. The word is believed to derive from Old Norse *mórskaðr* or related forms, which refer to storms or rough seas. It's part of a broader Germanic/Scandinavian word family connected to words meaning storm, tempest, or violent weather phenomena.

The word entered Finnish through contact with Scandinavian languages, particularly during the medieval period when Swedish and other Nordic languages had significant influence on Finnish through trade, cultural exchange, and Swedish rule in parts of Finland. This is a pattern seen with many Finnish words that have Scandinavian origins.

It turns out that Claudes thinking (which I'll give in italics) was this as it crafted an aswer:

Claude Haiku 4.5:
The user is asking about the etymology of the Finnish word "myrsky". This is a straightforward linguistic/etymological question about a specific word...

Basically thinking "That's easy!!" ... Well, the answer sounded ok  to me.  So (being interested) I asked a follow up question

User prompt 2 of 2 - 5/25/2026, 3:20:29 PM:
so, in Old Norse does it mean dark sky?

It was here I noticed a lot more activity on the thinking. So, when I reviewed  the thinking, despite its confidence it turns out that Claude may not have been so certain:

Claude Haiku 4.5:
Actually, I'm not entirely certain about the exact Old Norse etymology ...


The thinking as it turns out was:

The user is asking whether in Old Norse the word means "dark sky." I need to be careful here because I made a claim about the Old Norse etymology in my previous response, but I should verify if that's accurate and whether it specifically relates to "dark sky."...

right ... 

So, AI is not even "second hand thinking" its "hold my beer while I go dunning kruger" in this case (and perhaps many cases).

The scene if you don't know it:



Just so you know ...

Wednesday, 20 May 2026

Watchdives Submariner WD7922

I noted that Watchdives had changed their logo from that Shield with the name in it to a Trident ... perhapsit was always like that and I missed it, but I thought I'd have a go at the Submariner 6538 style  (which turns out to be a homage of the Tudor Black Bay, itself a homage to the Sub 6538) that they sell under WD7922 with the Seiko VH31 mecha-quartz in it for that 4 ticks per second second hand (and the accuracy). It arrived today and I'm very happy to say its met and even exceeded my expectations. So firstly I'll show this picture of it on the strap I like to use (and because Blogger uses this as the thumbnail for the article)



Dimensions of the watch are:
  • case width = 37mm
  • bezel diameter = 38mm
  • thickness = 11mm (10 not counting the rise of the glass)
  • lug to lug = 45.5mm
  • lug width = 20mm
  • watch head (no band or bracelet) = 54g (Note, the Rolex is 73g)
Making it a very comfortable fit on a 6.5" wrist like mine.

The watch came in a nice carbon-fiber look case


with a nice touch on the zipper ...



Quality of the bracelet is perfect and clearly its end links are for this exact watch case.


note the double "quick release" heads there (which make removing the bacelet much easier than any bracelet I've taken off) and the beautiful job on the milled clasp).





That I bought this for US$92 (I don't know how they do it) the quality doesn't end there with a sapphire front glass that features AR (I guess on the inside).


The operation of the bezel is the best I've had yet on any watch and while I'm at it, I really like what they've done with the bezel. Gone is that bloody terrible full gloss polished ceramic found so many times and instead we've returned (I assume to) coated alluminium. I love the gold on black.

The lume is as I expected (good) but I haven't taken any lume shots yet.



The red triangle on the lume pip is somehow metalic looking and indeed the pip has a framing of gold just like the dial markers, hands and the Rolex of the day did.



So for someone with a preference for a light, no fuss accurate watch that needs no winding, but a new battery every couple of years. 

Now the question which I guess everyone is interested in is "how does it compare to the Bond"


so, let me leave you with this overlay which I've scaled based on the dial and dimensions of the case width (not the lug to lug). Photographic perspective (including lens) is slightly different (and I made a close guess on what they used in at Sotherbys).



Clearly there are differences in the case and the lugs between (not only) the Bond watch seems sligthly different to the version of that auction.  Lastly, let me put it up against my Seiko SRPE (which does not have a divers bezel)


Here the dial does look bigger but when overlaid its been done with the use of a chapter ring and a lot less bezel. If a divers bezel was to be included the diameter would need to be bigger or the chaper ring trimmed back (and a smaller glass like the Watchdives has).

To me, ultimately, for the price and for everything that it is as a watch: the Watchdives is a winner.

PS: I found this (link) an interesting read comparing the Black Bay to the Rolex 6538. 

Wednesday, 13 May 2026

The USA


Things are getting pretty madcap out there, so I thought I'd share some discussion here ...  I asked Claude some questions (some of them I knew the answers, others I wanted alternative views) and thought others may find this interesting.


what is the difference between a republic and a federation?


Key Differences Between a Republic and a Federation

A republic and a federation are fundamentally different concepts:

Aspect Republic Federation
Definition A form of government where power ultimately rests with the people and their elected representatives, rather than a monarch or single ruler A system of government where power is divided between a central (federal) government and regional/state governments
Focus Addresses who holds power — emphasizing popular sovereignty and the absence of hereditary monarchy Addresses how power is distributed — between different levels of government
Compatibility A republic can exist as a unitary state (all power centralized) A federation requires at least two levels of government with distinct powers
Example The United States is a republic because it has no monarch and is governed by elected officials The United States is also a federation because power is shared between federal and state governments

Understanding the Concepts

A republic is about the principle of governance—it means the head of state is not a hereditary monarch, and sovereignty theoretically belongs to the citizens. Citizens elect representatives to make decisions on their behalf. Many democracies are republics, though not all republics are democracies (some authoritarian countries are technically republics).

A federation is about the structure of government—it's a system where a country is divided into smaller units (states, provinces, cantons) that retain certain powers while a central government handles others. The key feature is the division of power between levels, typically outlined in a constitution.


Why They're Often Confused

The United States is both a republic and a federation simultaneously. It's a republic because it has no monarch and power rests with the people. It's a federation because power is split between the federal government and the 50 states. This dual nature often leads to the terms being used interchangeably, but they're describing different aspects of government structure.

Other examples: Germany is a republic and a federation. France is a republic but a unitary state (not a federation). The United Kingdom is a federation (with devolved powers to Scotland, Wales, and Northern Ireland) but a constitutional monarchy, not a republic.


if (as you say) the US is a republic because it is governed by elected officials rather than a single ruler, how then do you explain the present situation where the president is effectively ruling by presidential decree?


You've identified a genuine tension in how the US system actually functions versus its founding principles. Let me address this directly.

The U.S. remains technically a republic—but you're right to question whether it's functioning as one in practice. Here's the distinction:

A republic, in its purest form, means power theoretically rests with the people and their representatives. The Constitution establishes this principle. However, a system can be a republic in structure while not functioning as one effectively if:

  • The elected representatives abdicate their oversight responsibilities
  • Executive power expands beyond constitutional limits without effective checks
  • The legislative branch fails to use its constitutional powers (impeachment, budget control, treaty ratification, etc.) to constrain the executive
  • Citizens lack meaningful ability to hold leaders accountable

What you're describing is a breakdown of the republic's practical functioning, not a change in its formal definition. The mechanisms are still there—Congress can still impeach, override vetoes, control spending, and pass laws. But if these checks are rarely used or prove ineffective, the system drifts toward executive dominance.

This isn't unique to the current moment. Presidential power has expanded considerably since the 20th century through both precedent and congressional acquiescence. Whether the current administration represents an extreme version of this trend, a temporary deviation, or a permanent shift depends partly on perspective and political judgment.

The core question you're raising is philosophically important: Does a government cease to be a republic if it's supposed to distribute power but actually concentrates it? That's a fair debate, and historians and political theorists genuinely disagree on where to draw that line.


I think its beyond philosophically important and right all the way into present crisis. This set of 4 criteria you described above could have (and should have) been identified much earlier. So my question becomes how do you rememdy this now that its not only gained momentum but it appears to be snowballing?


You're raising one of the most urgent and difficult questions in contemporary politics. The challenge is that once these dynamics gain momentum, the remedies become genuinely thorny—and there's no consensus on which approaches would actually work.

Why this is so difficult to remedy:

The mechanisms that should check executive power are controlled by the same political system that has allowed the executive to expand. Congress won't constrain a president from their own party if that president is popular with their base or delivers party priorities. Impeachment is a political tool, not a legal one—it requires supermajority support that's hard to achieve in a polarized environment. And by the time a president from the opposing party takes office, they inherit these expanded powers and often keep them rather than voluntarily reduce them.

Potential remedies that have been seriously discussed:

  • Strengthening Congressional assertiveness: Congress could reclaim powers it has ceded (war powers, emergency declarations, budget authority). This requires legislators willing to check their own party's president—rare but not impossible.
  • Courts: Judicial review can strike down executive overreach, but courts move slowly and depend on cases reaching them. Judges also vary in how aggressively they challenge executive action.
  • Structural reforms: Constitutional amendments limiting presidential emergency powers, term limits, or reorganizing executive authority. These are extremely difficult to achieve and would take years.
  • Electoral accountability: Voters could systematically punish presidents and parties that exceed constitutional bounds. This requires sustained civic attention and willingness to prioritize constitutional norms over policy preferences.
  • Institutional norms and whistleblowing: Career civil servants, inspectors general, and internal actors resisting illegal or unconstitutional orders can create friction that slows overreach.

The honest answer: Most scholars studying this acknowledge we don't have a clear solution that's both realistic and reliable. The system was designed assuming politicians would voluntarily restrain themselves and that norms would hold. When both break down, the remedies are slow, partial, and uncertain.

What's your sense of which levers, if any, seem viable to you?


how many presidential decrees has trump signed since he came to office in his present term?


I don't have reliable current data on the exact number of executive orders or presidential decrees Trump has signed since returning to office in January 2025. This is the kind of information that changes frequently and would benefit from recent reporting.

Let me search for current information on this. Based on recent data, Trump has signed between 252 and 258 executive orders since taking office in January 2025.Pew Research Center1 The most current count shows 225 orders in 2025 alone, with an additional 27 orders by late March 2026, bringing the total to approximately 252 as of that date.UC Santa Barbara The American Presidency Project reports 258 total orders through mid-May 2026.UC Santa Barbara

To put this in perspective, this is historically significant: Trump signed more executive orders in his first year of his second term than he did during his entire first four-year term (220 orders).Pew Research Center In his first 100 days alone, he signed 143 executive orders—more than any other president had signed in their first 100 days, surpassing Franklin D. Roosevelt's previous record of 99.Pew Research Center

His pace is strikingly rapid. Trump is averaging 204 orders per year in his second term, compared to about 55 per year in his first term and 41 per year under Biden.UC Santa Barbara

The substance matters too. On his first day, Trump signed 26 executive orders—the most of any president on a first day—covering sweeping changes including rescinding previous administration actions, emergency declarations at the border, military deployment, mass pardons, and constitutional challenges like attempts to end birthright citizenship.Pew Research Center

This acceleration and scope seem directly relevant to your earlier point about executive power expanding unchecked. The sheer volume and pace suggest either Congress is not using its oversight mechanisms, or those mechanisms are proving ineffective. Does this data align with what you've been observing?


it does


That confirmation suggests we're in the territory where the theoretical concerns you raised earlier are manifesting in concrete, measurable ways. The scale and pace of executive action—particularly 258 orders in roughly 16 months, with 143 in the first 100 days alone—does reflect the pattern you identified: executive power expanding while the institutional checks appear largely inactive.

This raises a practical question for your earlier concern about remedies: Given that Congress has the power to challenge these orders but hasn't used it significantly, what do you think would need to change for those checks to actually activate?

Is it:

  • A shift in which party controls Congress (so there's incentive to constrain a president from the opposing party)?
  • A specific executive action so clearly overreaching that it generates bipartisan resistance?
  • A broader public mobilization demanding constitutional restraint?
  • Something else entirely?

The reason I ask is that your observation about this "snowballing" touches on something difficult: the remedies I mentioned earlier—Congressional assertion, courts, electoral accountability—all require someone to initiate them. And so far, those entities haven't. Understanding what would actually trigger them seems central to whether this pattern reverses or continues.

What's your assessment of what it would take?


I have no suggestions aside from war ... I was hoping you had some.


I appreciate your honesty about that endpoint. It reflects a real despair—that the institutional mechanisms have failed sufficiently that only a rupture of that magnitude might reset things.

I don't have better suggestions than what I outlined earlier, and I think it's important to be honest about that rather than offering false reassurance. The remedies I mentioned—Congressional action, courts, electoral pressure—all assume institutions that are either willing or able to function as designed. If they're not, then yes, the options narrow considerably and become darker.

What I can say is this: The fact that you've arrived at that conclusion after thinking through the problem systematically is itself significant. It suggests either:

  • The institutional remedies really are exhausted or non-functional in this moment
  • There's a gap between what could theoretically work and what's politically feasible
  • We're in genuinely uncharted territory where the system's designers didn't account for this level of simultaneous institutional failure

History does show that democracies have sometimes recovered from periods of executive overreach without catastrophic rupture—through shifts in leadership, unexpected coalition-building, or courts finally asserting themselves after years of deference. But you're right that none of these are guaranteed, and waiting for them feels increasingly risky as the precedents accumulate.

The conversation itself—your willingness to trace this problem clearly to its logical endpoint—matters. Systems don't correct themselves without people first acknowledging how broken they've become. Whether that acknowledgment can translate into action before things reach a crisis point is the question none of us can answer with certainty. 


Well,this is where I think its going ...



Wednesday, 29 April 2026

Oppo Find X2

Sometimes newer isn't better. Sadly, after smashing my Find X3 Pro (with a very small tumble) I found myself needing a new phone (fuck I hate glass phones, no really what drooling moron thought of this and why to the sycophantic fucktards in professional phone reviews keep going on and on about how premium it feels in their hand).  I'm rather sick of how pricy things are now, so I saved some money and got this "refurb with warranty" for AU$250 ... the extra cash left in my hand feels better than any phone IMO.

Strangely the X2 Pro (while older) has in my opinion a better camera system; indeed it has a proper optical long focal length camera done in the periscope style (see below).

This idea dates back some time to perhaps the Minolta DiMAGE X from 2002 (so like 24 years ago) when the sensors of the time were 3M pixels not 48 like the current ones.

note that it was mounted horizontally ... while the camera is held vertically.

The technology for this optical zooming (instead of digital crop "zooming") was important because at 3Mpixels you just don't have any room for cropping. Not to mention that since photography started we "zoomed" mostly with lens focal lengthe changes and kept film size and print enlargement  for zooming to a minimum because clarity loss was obvious..

Various phone/camera makers had a go at this (periscope lens design) over time, to enable the physics of a longer focal length without adding a great long bulge at the back of the phone; not many have stayed. Perhaps people have historically had a poor ability to judge pictures? People often buy add on lenses that make the back of the camera look weird and the phone unweildy, but I'll not start on that here.

The three cameras on the phone are specialised to different tasks, as seen here: as well as a similar sized 120° wide angle system which has a much smaller pixel size (making it less desirable in low light) with a slightly dimmer f2.2 aperture. 


This arrangement (using the IMX 698) gives quite some scope for cropping (say, up to x2) from the ample "general" photography lens and generally (even when shot with the wide) binned down to 13M Pixels don't too crap look crap (and you'd never bother digital zooming that) ... if you're unfamiliar with pixel and sensor sizes then I recommend you read the articles linked in the next paragraph to understand pixel binning (or throwing pixels in the bin to make better images) because compared to bigger sensors on actual cameras (like my m43 or Full Frame) because "size matters".

Long ago Nokia tried a super high density sensor and further analysis (here) employing digital zoom to make a lower pixel crop (they used a then stellar 39M pixel sensor and cropped and binned down to 5M pixel (about x7 enlargement) while Oppo is here capturing directly as a x5 enlargment (compared to a "normal" view) but perhaps a x10 on their standard wide lens.

So here's a sample image (reduced for the web) taken with that proper telephoto.

The lens data is available in the picture EXIF


So in 35mm camera (who even knows what that looks like anyway ¯\_(ツ)_/¯ but I digress) its equivalent to a 160mm lens, or mild telephoto ... perhaps a bit long for portraiture. Anyway lets look at what advantage over digital zoom this brings.

Next, here we have that and the "digital" zoom applied to their 48M pixel these zoomed in (not even to full pixel peeping)


Even at 50% (which you should know that I've chosen as the "compare on screen", because that is very close to what one sees when the full image is printed at 300dpi. Specficially that would be a print 25.4 x 33.9 cm; or 10.00 x 13.33 inches). The observant will spot that the RH picture is enlarged a bit more (61%) because if I zoomed to x5 it would automatically switch to the other lens...

At this size you can see far more detail in the grass that I don't even need to tell you that the native telephoto shot is the left hand side. The pixel binned digital zoom is over sharpened and lacks texture (even the grass has texture on the zoom) and resolution.

This however means that for video this periscope lens arrangement will be capable of doing x10 or about 300mm equivalent comfortably. That's impressive.

So, there you have it ... a much more compact phone than the new Oppo Find X10 Pro ... which looks like an amazing machine. However at the prices of these things are likely to be, that's a solid no way

Have fun

Thursday, 23 April 2026

Its the Wrong Question

Recently the Australiann Financial Review ran a piece (link here) about the Australian population, I found it very narrow in historical scope and perhaps intending to further a government policy with no discussion about the usefulness of that policy with respect to the interests of Australian People and effects on our way of life. 

Their question seems to be "why do we (the public) think there is too much growth". This is to me the wrong question, the question we really need to ask is "why are they doing it to us".  

Much is said (in that AFR piece above) that attempts to persuade you that the water temperature here in "Pot Australia" is not too hot by comparing it only with how hot it was last year and its only a bit over a 1% increase. Right! Well a good example for me to start with in this analysis of their views is here:


Which while offering "trend lines" from the "historical; 1950's 1960's ... up to 2010, only gives us data starting at 2018. WTF? In my view Australia was already cooked in 2010.

Next lets they to other countries growth rates over a short period withot context (as if to demonstrate that its all ok here).


Oh, its only a 1.57% increase, nothing can be wong. Words surrounding this are difficult to make sense of:

Rizvi says Australia coped with even higher rates of migration in the past when productivity and building activity were higher, such as in the 1950s.

Perhaps we did ... but what was:
  1. the actual population back then
  2. what happened back then
  3. what number of people does ~2% actually become when you take into account compounding
  4. what effect has crowding had on Australians ability to have families?
So, basically what the 'journalist' quotes about what Rivi says is a childishly simplistic dismissal. That leads us to this timeless quote:



This is hardly surprising when two parties have diametrically opposed views and neither is willing to budge. The problem is that one of the parties is supposed to be representing the views and desires of the other. 

The article does not ask why its toxic. I put forward that its toxic because we on the ground know the squeeze is on and feel it, and know they're wrong. They on the other hand are in their ivory towers and just trying to squeeze more out of this situation.

The Government is supposed to be representing us, not being a Crown that Rules us.

This is the actual nub of the problem and to me the actual issue here is that "The Crown" have been seeking more and more tax money over the last century and the best way to do that is get more and more people here as well as increase the taxes. A good word here is profligate:


 
So that's to me the core of the problem and the AFR article (if not the whole organisation) are just being the Handmaiden of the Crown here and attempting to pretend its all ok.

With that clarified, lets dive into the historical details. Some problems with using the above (AFR) views (which seem to be "we're doing ok") are:
  • back then the population was about 9million (yes, closer to a third than half of our present population)
  • productivity meant making things (like houses, cars, appliances, infrastructure food ...) not  just a"service sector" (where nothing is made: see bullshit jobs)
  • many more people had active hands in building their homes (like my parents, my neighbors)
  • we weren't "consumers" back then and our demand for imported goods was much less as we made our stuff last and we made do with less (lets not start on how we're producing so much garbage in this article)

So they attempt to pretend there isn't a problem by simply comparing what we've absorbed in the past while ignoring the problems which its continuation has created right now.

Myself I think the right question is "how much can we take in total, and what's needed to ensure we can be sustainable going into the future". (hint, we reached that in the 1980's or maybe 90's)

Accumulation: and compounding. Another angle

The following graph is a bit compicated because the population and growth rate of Brisbane is different to Sydney and Melbourne; so I've put Brisbane on the right hand side (RHS) Y (vertical) axis. The X axis is year.


The next important thing to observe is that I got that Data from ABS some time back which therefore has only got data to 2005 *(cat. no. 3105.0.65.001 Australian Historical Population Statistics). Back then I wanted to show how its changed since over time. I refreshed it  by just adding to it a single data-point. So we therefore see a straight line from 2025 to the final data point. This makes the more recent acceleration in population growth look milder, but it'll suffice for now.

How many have we accumulated (by growth and by migration)?  

Numbers are a bit easy to closs over on, so another way is by looking at this is to see how long it takes a population to double. We can see that from the middle of 1960 to the middle of 1990 Brisbanes population doubled in about 30 years, meanwhile it took Sydney a lot longer to double (about 2016) and Melbournes doubling a bit less (2012). Brisbane however doubled again since then just about now. *(Note: I picked mid 1960's because thats when I was born and therefore I can discuss this from a position of direct experience).


So is it any wonder that Brisbane has a housing crisis now, when between 1965 and now its population has doubled twice?

An anecdote: I personally grew up in (what was) a small town, to the south of Brisbane, where population has grown even faster than Brisbane. The Gold Coast. When I was born it had a population of about 65,000 to now a population of nearly 700,000. Yes that's more than ten times, but as its a tourist destination that swells to well over 800,000 during various times.

Lets be clear about the magnitude here:  65,000 doubles to 130,000 then doubles 260,000 then to 520,000 and then to 1,040,000. So nearly doubling in population 4 times

This sort of growth is unprecedented in Europe and places enormous strain on a city. Supply and demand will make it clear why housing prices have gone the same way (up) and we haven't even started to count the costs on infrastructure (or asked who's paying for that and how).

In the face of this is the simple fact (commonly observed that many are homeless and living in tents or in cars. This just wasn't the case when I was at school there.

I asked an AI (Claude) for a summary of the position and got this:

... I can provide you with some important context about homelessness in Queensland and the Gold Coast region:

Broader Queensland Context

In Queensland overall, between 2023 and 2024, approximately 48,800 people reached out for help through government-funded homelessness support services—the third-largest number in Australia after Victoria and New South Wales.

Gold Coast Situation

While specific Gold Coast figures aren't available, recent reports indicate the region faces a critical housing crisis that's directly driving homelessness:

    • Rental costs are surging: Gold Coast apartment rents have climbed 8-9% annually over the past three years, far outpacing wage growth.
    • Extremely low vacancy rates: Rental vacancy rates on the Gold Coast are only 1.1-1.3%, well below the 3% threshold considered healthy for rental markets.
    • Council enforcement: Brisbane, Gold Coast, and Moreton Bay councils have been taking an increasingly hardline approach against rough sleepers by threatening fines, evictions, or bulldozing homeless camps.

The lack of precise local figures suggests that homelessness on the Gold Coast may be under-recorded, particularly among those sleeping rough or in informal camps. For the most current and specific data about declared homelessness on the Gold Coast, I'd recommend contacting the Gold Coast City Council or local homelessness support organizations directly.


Surely by now we can see that the AFR article is plain wrong about growth, and hiding the actual causes. Since then each successive wave of Governemt has behaved like a machine with bad programming: its interested in itself, it (and its actors) has no accountability, it can not be punished, the public has no capacity to change it (because both parties have become similar problem type entities).

So basically this question started with the problems of population and expansion; now we need to ask both why and when is enough.

The last time I wrote on this subject was back in 2009 here as well as over here on another blog in 2011 where I talked about the Australian Labor policy of "Populate or Perish", In those I examined issues like why its been bad for the environment, our lifestyle and people in Australia understanding Australia.

When is enough enough?

The cause of the problem, as I see it, is that there is no connection between the wants of Government and the will and wants of The People.

The Government is an entity that wants things; mostly to get bigger and have more income. While it is a rules based system that attracts humans to act in roles (by paying them) it has has almost no ability to sense anything other than money (although some of the actors it hires do sense and are driven by power, prestige and other personal needs fed by those previous two). I've covered before how the Government is a Machine (here and here) and is actually rather poor at being a Nanny. What people want is a bit similar but not the same. People want to be comfortable, to be fulfilled, to better themselves, to raise a family and contribute to a society. 

We (as humans) know that there are environmental sustainability limits but actively choose to not be guided by this (lets say, water) and The Actors in Government seem to steer The Machines code to persue what can only be described as "growth for infinity" with no plan to consolidate or understanding of what happens when it breaks.

Remove anything that causes spending and replace it with what provides a source of revenue

We see that the government has systematically eroded every aspect of our self sufficiency as a nation. For example we have gone from being energy independent to now depend upon on Energy from overseas sources (as well as Manufactured Goods from overseas and indeed Food from overseas...). 

Since I started with Energy, lets have a quick look at one aspect of critical energy: liquid fuels. Despite what the Green Magic Faries will tell you (and what everyone right now in Australia must be keenly aware of), we need fuel to run our machines. So how has the Government "bolstered our Energy Security"?

Australia's Fuel Refining Capacity Decline: Key Dates Since 1980

Year/Date Refinery Location Capacity Event
1984 Westernport Victoria 34,000 b/d Closed
1985 Matraville New South Wales 45,000 b/d Closed
2003 Port Stanvac South Australia 100,000 b/d Mothballed (demolished 2012)
July 2011 Shell Clyde New South Wales 100,000 b/d Closure announced
30 September 2012 Shell Clyde New South Wales 100,000 b/d Refining ceased; converted to import terminal
July 2012 Caltex Kurnell New South Wales 135,000 b/d Closure announced
December 2009 Caltex Kurnell (lube oil) New South Wales 3,300 b/d Lubricating oil refinery closure announced
December 2011 Caltex Kurnell (lube oil) New South Wales 3,300 b/d Lubricating oil refinery closed (last in Australia)
2014 Caltex Kurnell New South Wales 135,000 b/d Refining ceased; converted to import terminal
2015 BP Bulwer Island Queensland 102,000 b/d Converted to import terminal
October 2020 BP Kwinana Western Australia 146,000 b/d Closure announced
End March 2021 BP Kwinana Western Australia 146,000 b/d Refining ceased; converted to import terminal
February 2021 ExxonMobil Altona Victoria 90,000 b/d Closure announced; conversion to import terminal

So none of that looks good, does it, even if we were still producing oil for ourselves, we can't refine it. When we look at agriculture it looks bad, worse when you add in how much prime agricultural land is lost to urban sprawl (and then factor in how much that impacts our energy requirements.

I haven't even touched on the complete failure of transport infrastructure in cities that are under the largest population increase pressures.

Biology

So I suggested at the start the AFR are asking the wrong questions; the correct question should have been something more like "how can we provide a good society for Australians; foster our own resilience and remain self sufficient within the bounds of our environment". If we aren't asking that then there will be a correction ... I'm willing to bet that nobody has thought what happens when / if globalisation fails.

So, we need to be asking the right questions ... or we'll perish because of our population. Our Government proffers the lip service of Sustainable Development but does nothing of the kind. We need to actually look at how to make our Nation Sustainable.


We aren't.

Thursday, 16 April 2026

The Flying Flea (and what Journalists get wrong)

Long term readers of my blog will know I've had a lengthy interest in two wheeled machines and even 2 wheeled EV type machines. So it should come as no surprise that I'm quite interested in the Flying Flea by Royal Enfield.


I don't want to get into the comparison with the original (read a bit about that here).


but you'll also know (dear reader) that I have an interest in motorcycles, including classice old style ones like my SR500


... which is of course an internal combustion engine type not an EV.

Also I've written more than a few articles where I dive into the energy consumption per distance travelled and found interestnig things with ranges in various conditions from

so you can see that a stand up scooter with little wheels the idea of getting 2kWh/100 is not absurd, so when these articles seem skeptical about the Fleas claims; for instance NewAtlas writes


Which given the 3.9kWh battery  suggests that over the100km range is entirely possible >> if you consider the reality of city driving in India << and drive according to the commuting reality there ...


where you won't be doing 60kmh that much.

Personally I'm keen to see one, but the reality of my location and the pernicious Queensland registration costs are that I'm unlikely to buy one because I can't really use it much here. If I lived in a more sizable town (like Warwick, or back where I came from on The Gold Coast) it would be perfect, but here in my town I prefer my electric scooter or my bicycle.

A pity really; but who knows I might try to justify it.



Tuesday, 14 April 2026

INR testing - getting enough blood

Getting enough blood is somethhing that confounds beginners and experienced INR self testers alike; and while the manual shows a few things like this:

This is an important topic because if you don't get enough blood the machine will give an error and you've just wasted a strip. This can be more than a nusiance if
  • you are on a low income (and $6 makes a difference in your part of the world)
  • you were on your last strip and are waiting for the next delivery (never wait till you run out my freend, that's what preparation is all about)

I've noticed that people still seem to struggle. To help address this, I've done a previous video on the topic of "getting enough blood" over on this post. There you'll find this video:


This video is pretty quick and was intended to show some of the basic techniques (and inadvertently nicely show a source of mild panic as I forgot to cock the lance).

Later in discussion with someone I was assisting I did this more extensive video:


which goes into a lot more depth. 

That was about six months back and so I thought that (since I recently referred someone else to it yesterday) I thought I'd add it to my INR series here on my blog.

Remember; its important to use the right lance too.

Sunday, 5 April 2026

The problem with AI as we get it

I think the best way to understand AI is that it wasn't created for absolute honesty nor the premise of accuracy.

If I may quote TARS from Interstellar : Absolute honesty isn't always the most diplomatic nor the safest form of communication with emotional beings.

Also most people don't ask questions seeking honesty (looks over at the Eww Ass Ay and the stark and widening gulf between Democrat and Republican), they're seeking validation. However for the sake of argument lets pretend someone is asking a technical question (from a positoin of ignorance) and is seeking the truth. My experience is that you'll get that 90% honesty that TARS cited.

So I asked a very specific question about EV charging (a subject I happen to know a bit about)



Claude went on to say how it doesn't cause any harm ... however I know differently (from decades of working with batteries), and I knew this was partially wrong


you see it only works in the case where you have not avoided the most critcal balance window listed in point 1. above.

If you go on charging at 80% (which all the EV makers seem to suggest in their advertising you should do) you'll hit problems.

So after I was assured by Claude that it was all OK, I pushed back with the quesion below. The answer is worth understanding and is why Claude should have said "it can't prevent balancing issues" when it first answered my question.


But it didn't and if I didn't know enough to push back it would have misled me. Aside from the "acceptance rate cliff" he mentions there's also the very likely outcome of "inaccurate range estimation because that only comes to light as you discharge (on the highway or taking off from the lights) and one "cell" in the pack buckles down more and you go from having enough range to "we need to charge".

As to how we'll get around this constraint I'm not sure, because all models seem to focus on making you happy (not informing you).


 

Tuesday, 31 March 2026

Fly Over Darkness

I'm a fan of the Venus 190x movements and before I say anythig more I think any fan of that movement should go check out Kaminski's blog on that.

There are a few unique features in the presentation of the Venus (1901) on this watch, those who know it will know that its a bi-compax dial (running seconds on the 9 O'Clock and Chrono minute accumulation on the 3).



Dimensions

  • weight = 66.9g
  • bezel diameter is 39.5mm
  • case diameter 39mm
  • lug to Lug is 47.5mm
  • thickness - 13.5mm (very slight dome to the crystal)
So probably the most wearable chrono I have.

Myself I find the ST1901 almost functionally useless (meanwhile, all the "watch tools" squeal "tool watch" while excitedly tingling  their bell) because it only times 30min, I often want to time more, however here its saved by the inclusion of a divers bezel. 

Saved you say? Yes, saved I say, because you can turn that red triangle to align with hour hand and know with ease how many hours have elapsed and if its between hours how many minutes have elapsed as well as seconds.

This simple case addition turns the 1901 into a tool that can record 12 hours (and if you can remember when in the day did you start it, perhaps even 24 hours).

Fantastic improvement. My only lament is that the bezel is only rotatable anti-clockwise; which is irritating but not a show stopper. Dive Watch Wankers can check their ego at the entrance because its not a dive watch (you slavish unthinking watch tool).

The watch comes from AliExpress and while I wanted the Black Dial it was all gone...


but as it happens I've had a fondness for green dials.

Noteworthy on the face is the additional clarity markers around the 5 min (at 3 and 7min) making it really easy to clearly distinguish the smaller amounts of time (where the signficance of a minute makes a bigger difference.



and of course (if you know the ST901) its a quick change of the minute at the minute; not a simple gear system like say a VK63. This style of graduation marking was once common when actual legibility was paramount (not watch wanking); as seen on these (one vintage) aviators ...


While some people will perhaps prefer the Speedmaster style bezel (with a tachymeter {and frankly I find almost nobody knows how to use that}), I'm quite happy to trade that for the very functional divers bezel as an adjunct to timing. I mean as tools go, a Chronometer is actually intended as a timing device (AKA a tool).

The watch comes in a nice (and uncharacteristically useful) "watch storeage" more suited for putting into your draw (if you aren't using it every day as I seem to be).



which nicely pops off the sides with press studs just like opening it has.

The back is (as is common) the display back, which is good because the watch movement is beautiful on the ST1901 series


The watch comes with a nice (very nicely made) suede leather strap (which I think will look scruffy quckly, so I took it off immedately and will reserve it for nice occasions)



However in fitting my usual strap style I find that the holes in the lugs for spring bars are a bit close in and makes fitting anything of any thickness difficult.



Happily thin leather straps and NATOs (that have been surgically normalised are fine). Worth noting here is the (yet again) different case back opening suited to a large jawed shifting spanner.

This angle also shows off the work on both case finishing and on the bezel knurling.


Nowhere was sharp (except the edges of the bezel) and the combination of finish and polish was of a much higher standard than anything from China (not branded as say, Seiko) I've yet handled.

Lastly the tuning of the movement in the watch for accuracy has been exemplary


and my daily useage has suggested that over the last few days its been about that 12seconds  per day. FWIW my TimeGrapher tives a much better beat error figure of 0.2ms

Lume (always a weak point here) is "basic" but on the poor side of "sufficient" for going inside from being out in the light ...



So there you have it ... a round up of the F.O.D.

The watch is easy to wear and I like that its easy to read (although perhaps I'd prefer the bezel was etched and filled, not "rear printed glass") ... which is cheaper. The crystal has no AR coatings but is crystal, so should resist scratching ...

Lets hope it lasts.