Friday, 20 November 2026

T-Max gets a new seat cover

Back in 2017 I bought this 2006 T-Max with about 90,000km; since then she's been a good reliable work horse with a few issues caused by age and previous owner neglect. So the seat cover has lasted 20 years. A testimony to Yamaha (and nothing like what modern resource greedy cheap Chinese EV's are like).

I have been wondering if the bike would die a few times, but all the problems so far have been easilly solved and or not major.  In this case I've been procrastinating for a while but I finally got around to getting a seat cover for the 2006 T-Max because it had actually split (and my "repairs" looked crap):

Fig 1

I stripped off (pulling each of the staples out and many were rusted and snapped); you can see the seat is basically stuffed and leaking ...


Note the two small loops with string attached, they go through gaps that can be seen where the "passenger seat foam" joins the "rider seat foam". This looked neat but I think it contributed to the early cracking in the circle in Fig 1 above. The new seat cover ignores that and I think its a simpler and hopefully robust design.

So the foam is discoloured but otherwise still good. I left it in the sun a few days to dry.


I didn't take any pictures of the process (because it was a bit of a multi day struggle) but basically I slowly stretched the seat cover over the seat starting from the front and working out in the sun to keep it hot (but not too hot).




So then all that was needed was to refit it to the bike...






Notes

  • get a good stapler, if you want to get it neat you'll totally need something with a littl bit of a nose on the end to get into tight places
  • get the right staples, look at what you pull out, seek the same. Measure them and get a bit familiar with what staples there are (and trust me, staple sizes are a red hot mess)
  • get some medium size "bulldog clips" just wide enough on the back to clip onto the seat frame (which is plastic)
  • clip it on and work around it making sure that you keep checking its straight. I ended up with 12 clips around the back half to hold it all in the right spot
  • finally, when it looks good, remove a clip and staple there, work around like that
Best of Luck


Monday, 2 November 2026

Shed Battery LFP

Back in August I wrote about the need to replace my shed 24V battery; which feeds an inverter and is fed by a solar panel. That little freebie was basically insufficent for heavier roles but got me by. I am however wondering if I've gone too far with my choice to go 100Ah 24V LFE, but I don't think so. Anyway, my cells arrived the other day and so I've put the pack together and thought others may appreciate some notes.


They look very neat and well finished, and so I wanted to weigh them, this is 4 cells on the bathroom scale.


Which means that they're a lot lighter than my Lead Acid which weighs in at 13.88kg per 12V.

I decided to arrange them in a side by side (similar to what I'd done with my Lead Acids).


unfortunately the metal strips supplied were not quite long enough to reach across and so I needed to use a cable. I'm not sure at this point if I'll keep that or change it to some solid copper.

Next I added the balance wires for the BMS harness


and its noteworthy that this arrangement is missing a wire when using the Jikong BMS as this also needs a sensing wire for the whole pack.Its on the second plug and separated from the remainder of the wires. Its important because the system will not function properly without it.


here it is attached to the last positive... and pictured with both loom parts plugged in ... 

I would have liked to "de-pin" the un-needed wires, but they're stuck in with resin. So I've just bundled them up and put heat shrink over the bare pre-tinned tips for the possibility of use at a later date if I decided to take this pack into 48V territory (making a 4.8kWh pack).


All is functioning well on the bench test... ... plugged into the solar panel (via the solar charge controller). I don't think however it'll get to much higher voltage than that because my panel seems to be the limiting factor (in combination with the slow climb after 3.4V with LFP.



and the phone app is reporting everything nicely ... once I tweaked the parameters


So the final position (for now) is like this (because I didn't want to move my inverter or alter the wires)

pack in location

I thought about putting it in a case but I wanted ventilation, so I've relied on the pack basically having structural integrity because:

  • its stationary, the cells are flat bottomed and sides are straight
  • each cell is bound to another at the top with a solid copper bus-bar and bolted
  • duct tape around the outside is flexible and gives me a great place for making thermal camera images identifying heat (same goes for the copper bus-bars), beware of shiny things when using IR to identify temperature.
The top is just "bracing ply" and is there mostly to just keep dust off the top of the pack and makes for a good place to put the +ve terminal (which is not under BMS control, its neative side switching).


Here you can see the pack orientation of series up one side and back the other, and that it places the active negative and positive on the inside of the "front". I've added a bent bit of copper bus-bar (half the thickness of the internal series connections) which is a deliberate move. My logic is that it will carry 40Amps (based on its cross secional areas) without problems and should indeed do 80Amaps continuously (but that's on the edge). So to make that an indicator that's easily read from the outside (without lifting the lid) or even touched to identify if its hot to verify pack critical parameters.

I guess next it'll be time to do a discharge test.